Italiano
-
Electronics, FSR Race, Switches
Power Switch – RX Switch – FSR Race
The SkyRC Power Switch is an electronic switch to turn on and off the radio device on board the model.
Compatible with NIMH and Lipo batteries, it incorporates a low battery signaling function, but does not stabilize the output voltage, so a Lipo battery can only be used with HV systems or with voltage stabilizers.TIP: (If with the RX battery charged while operating one or more servos, the switch LED flashes red, it means that you have low amperage in the RX battery or that a servo is particularly straining and therefore it will be necessary to check before launching model)
SKU: 447944 -
Battery, RX Batteries, Electronics, FSR Race
Battery RX LiFe 2S 3000mAh 35C V2 – JR FSR Race
Compatible with radio box TFL art. 755B31
I recommend charging it at 1.0A with balancer and in life mode, do not use it to put it in storage like Lipo when you have finished using it.
New line of FullPower lipo batteries for receiving power supplies (RX), equipped with silicone cable and UNI plug (JR type).
For a good yield and duration of Li-Fe battery packs it is recommended to balance them while charging using suitable tools.
Fullpower batteries are suitable for a charge up to 5C (five times the battery capacity) however, if you do not have particular urgency, it is recommended
SKU: 447924 -
Brushless, Outboard, Electric Motors
Outboard Brushless – B54210
TFL Outboard Drive System Gear Drive 3660/2075KV SSS Motor,W/O Prop, Shaft 4mm DD
- Outboard motor made by CNC and with fiberglass cowl
- The transmission between the motor and the propeller takes place by means of gears.
- Recommended for boats from 65cm to 100cm
- Recommended ESC 120A.
- Recommended batteries: LiPo 4S
- The propeller shaft is 4mm diameter with Drive Dog.
- The package does NOT contain the propeller
- Propeller recommended with 4S: https://www.tflhobby.eu/en/eliche/elica-3-pale-alum-cnc-d36mm-o-3614351/
SKU: B54210 -
-
Material and Glue, Hand Tools
Universal activator for cyan 200 ml
Universal spray activator for cyanoacrylate glues, also suitable for special glues such as DEPRON, EPP, etc.
It speeds up the adhesion of cyanoacrylate glues, a sprinkle on the part to be glued is sufficient, after applying the glue, to block the pieces to be joined in a few seconds.
Convenient 200ml spray pack.
Made in Italy- Glue type: Activator for cyan
- Quantity: 200 ml
- Usage: Cyanoacrylate glues
SKU: 113845 -
-
-
Battery, RX Batteries, Electronics, FSR Race
Battery RX LiFe 2S 3000mAh 35C V2 – JR FSR Race
Compatible with radio box TFL art. 755B31
I recommend charging it at 1.0A with balancer and in life mode, do not use it to put it in storage like Lipo when you have finished using it.
New line of FullPower lipo batteries for receiving power supplies (RX), equipped with silicone cable and UNI plug (JR type).
For a good yield and duration of Li-Fe battery packs it is recommended to balance them while charging using suitable tools.
Fullpower batteries are suitable for a charge up to 5C (five times the battery capacity) however, if you do not have particular urgency, it is recommended
SKU: 447924
-
-
FSR Race, Coupler & Joint, Zenoah Plier
Flywheel with Coupler for Zenoah 27CC – 529B52
Flywheel with Coupler 6.35mm for Zenoah 27-29-32c.c., compatible with brand gas motors: Zenoah, Tiger King, SG, e BZM Motors.
- Total lenght=47mm
- M6mm -internal screw for fix to motor shaft
- 6.35mm – flex steel coupler
- Outer Flywheel diameter=44.5mm
For open and close the coupler, you need two wrenches of 16 number
SKU: 529B52
Products Grid
Ultimi inseriti
ESC ZTW SEAL 90A SERIE G2
This is the new series of ZTW 32 Bit G2 90A ESCs which support 3 to 8S batteries with 6V/7.4V/8.4V 8A SBEC (receiver power supply), the design is new and narrower than the previous series.
The SEAL G2 series is specially designed for RC hulls, with a waterproof shell.
In order to protect the electronics, the motor and the batteries, the ESC has an electronic system that reduces power in the event of overheating or low battery voltage.
Key Features:
1. New generation electronics that resist large instantaneous absorptions.
2. Adopts high-performance 32-bit microprocessor, the operating frequency is up to 170MHz which gives the G2 sere esc higher computing capacity.
3. The waterproof design (rates as IP 67) allows this ESC to operate in wet conditions and features water cooling applied to a metal plate to ensure efficient heat dissipation.
4. Super smooth and accurate throttle linearity makes the ESC suitable for various types of hulls: mono, cat, F1 or reproductions.
5. The ESC has two driving modes for different applications: “forward only” and “forward and reverse”. (I do not recommend reverse if you have a flexible axle!)
7. Multiple Protections: start, overload, low voltage cut-off, signal loss, phase loss, over-current, abnormal supply voltage, overload protection.
8. Compatible with high rpm brushless motors and compatible with most motors on the market.
9. Support programming via phone app or LCD program card, operation easier and more convenient (ZTW Extra App adapter or LCD program box needed G2.)
Technical specifications
Continuous current (A): 90 amps
Inrush current (A): 540 amps
Voltage: 3-8S Lipo
BEC output for the receiver: 6V/7.4V/8.4V 8A – connectors fit the classic JR ones, they are also good on Futaba
Power Cable: 12 Gauge80mm-Red/80mm-Black
12 Gauge Motor Wire 65mm – Black
The throttle works in both forward and reverse gear or you can lock the reverse function for racing safety.
Optional programming with G2 LCD programming card.
Case Dimensions (Cables Not Included):
Length: 88mm
Width: 38mm
Height: 24mm
Weight: 110g
Engine Support Zenoah 260PUM AND 290PUM
ENGINE SUPPORT ZENOAH 260PUM and 290PUM
made of AISI 304 steel with laser cutting and cnc bending technologies
allows you to mount your Zenoah with maximum precision between the rails of the hull,
adding the M6 silent blocks 20mm diameter and 15mm wide, you reach the width of 127mm equal to the T-bar Art.526B10.
On the carburetor side, 2 x M3 threaded holes have been prepared to fix the throttle arm at 90 degrees.
To reassemble the starter strap you need a thickness of 3mm.
