-
Electronics, FSR Race, Switches
Power Switch – RX Switch – FSR Race
1 in stock
The SkyRC Power Switch is an electronic switch to turn on and off the radio device on board the model.
Compatible with NIMH and Lipo batteries, it incorporates a low battery signaling function, but does not stabilize the output voltage, so a Lipo battery can only be used with HV systems or with voltage stabilizers.SKU: 447944 -
Brushless, Outboard, Electric Motors
Outboard Brushless – B54210
1 in stock
TFL Outboard Drive System Gear Drive 3660/2075KV SSS Motor,W/O Prop, Shaft 4mm DD
- Outboard motor made by CNC and with fiberglass cowl
- The transmission between the motor and the propeller takes place by means of gears.
- Recommended for boats from 65cm to 100cm
- Recommended ESC 120A.
- Recommended batteries: LiPo 4S
- The propeller shaft is 4.76mm diameter with Drive Dog.
- The package does NOT contain the propeller
- Propeller recommended with 6S: art. 3715 (D37mm, 1.5 “pitch) (https://tfl-hobby.tempestrcboats.com/eliche/elica-2-pale-alu-cnc-37mm-3715/)
SKU: B54210 -
-
Material and Glue, Hand Tools
Universal activator for cyan 200 ml
5 in stock
Universal spray activator for cyanoacrylate glues, also suitable for special glues such as DEPRON, EPP, etc.
It speeds up the adhesion of cyanoacrylate glues, a sprinkle on the part to be glued is sufficient, after applying the glue, to block the pieces to be joined in a few seconds.
Convenient 200ml spray pack.
Made in Italy- Glue type: Activator for cyan
- Quantity: 200 ml
- Usage: Cyanoacrylate glues
SKU: 113845 -
-
-
Electronics, ESC, Electric Motors, Section M
ESC 40A Pro
Out of stock - Made to order
Nominal 40 Amp water-cooled regulator (Max 60 Amp x 5 sec.)
Weight complete with cables gr. 45
Max dimensions: 68 x 13.5 x 26.5 mm
Built to manage brushless motors.
Possibility of programming through its card art. Hobbywing 30501003
Recommended accessory for the mini class (Minimono and Minihydro) or all those boats with a length not exceeding 50 cm and weight not exceeding 650 gr.
SKU: ESC_40A_PRO -
Servo
Servo – LW-20MG Waterproof
Out of stock - Made to order
Waterproof Servo
- Torque (4.8V): 16.5 kg-cm
- Torque (6.6V): 20.0 kg-cm
- Speed: 0.18 sec (4.8V) | 0.16 sec (6.6V)
- Operating voltage: 4.8 ~ 6.6 DC Volts
- Weight: 60g
- Bearing Type: Ball Bearing x2
- Motor Type: DC Motor
- Gear type: Copper & Aluminium
- Operating Temperature: -20°C ~ 60°C
- Working frequence: 1520µs / 333mhz
- Size: 40.7 x 20.5 x 36.5mm
SKU: LW-20MG -
-
Brushless, Electric Motors
SSS Brushless Motor W/O Water Cooling 2960 series
2 in stock
- Brand: SSSMotor
Diameter (mm): 29mm
L (mm): 60mm
D-shaft (mm): 3.17mm
Poles: 4
Tum: 4.5D
Max Amps (A): 65
Max Voltage (V): 20
Max Power (W): 1300
Idle Current (A): 1.7
Max RPM: 60K
Weight (g): 170g
Cooling: No
SKU: 2960 - Brand: SSSMotor
-
-
FSR Race, Coupler & Joint, Zenoah Plier
Flywheel with Coupler for Zenoah 27CC – 529B52
Out of stock - Made to order
Flywheel with Coupler 6.35mm for Zenoah 27-29-32c.c., compatible with brand gas motors: Zenoah, Tiger King, SG, e BZM Motors.
- Total lenght=47mm
- M6mm -internal screw for fix to motor shaft
- 6.35mm – flex steel coupler
- Outer Flywheel diameter=44.5mm
For open and close the coupler, you need two wrenches of 16 number
SKU: 529B52
Products Grid
Recensioni
Ultimi inseriti
Engine Support Zenoah 260PUM AND 290PUM
48 in stock
ENGINE SUPPORT ZENOAH 260PUM and 290PUM
made of AISI 304 steel with laser cutting and cnc bending technologies
allows you to mount your Zenoah with maximum precision between the rails of the hull,
adding the M6 silent blocks 20mm diameter and 15mm wide, you reach the width of 127mm equal to the T-bar Art.526B10.
On the carburetor side, 2 x M3 threaded holes have been prepared to fix the throttle arm at 90 degrees.
To reassemble the starter strap you need a thickness of 3mm.
LCD PROGRAM CARD
Out of stock - Made to order
This programming card is specifically designed for the ZTW Series electronic speed controls.
HOW TO USE THE LCD PROGRAM CARD:
The LCD Program card can be used to set up the Gecko series brushless ESC produced by ZTW Model.
Users can choose their desired parameter at any time.
It has 2 user methods as follows:
SPECIFICATIONS:
Dimensions: 91mm*54mm*18mm (L*W*H)
Weight: 68g
Power supply: DC 5V~12V
